如何使用點膠機做好點膠工作？
如何使用點膠機進行點膠工作
How to use dispensing machine for dispensing
1、固化要素:關于膠水的固化，一般廠家都給出了溫度曲線。一般在室溫下即可固化，在實際操作中應盡量選用較高的溫度進行固化，使固化后的膠水達到強度和硬度要求。
1. Curing elements: for the curing of glue, the general manufacturer has given the temperature curve. Generally, it can be cured at room temperature. In actual operation, it should be cured at a higher temperature as far as possible to make the cured glue meet the requirements of strength and hardness.
2、關于膠泡的點膠機在點膠的過程中會影響產品的質量，所以在放膠前一定不要有泡。
2. The dispensing machine of the rubber bubble will affect the quality of the product during dispensing, so there must be no bubble before dispensing.
3,真空吸入閥必須安裝在配藥機,由于真空回吸功能是防止膠在配藥機不是調劑膠還泄漏,如果安裝這個工具可以合理地調整真空吸入閥,以進一步控制滴和繪畫兩種情況。
3. The vacuum suction valve must be installed in the dispensing machine. Since the vacuum suction function is to prevent the glue from leaking in the dispensing machine, if this tool is installed, the vacuum suction valve can be adjusted reasonably to further control the dripping and painting.
標準4、針和類別:針標準會影響在調劑的過程中膠粘劑范圍和精度,當壓力,噴嘴針越大,速度越大,所以要分配的基礎上機器生產產品的侵入性的標準錨點膠針,針直徑長度保持膠點直徑的一半,效果很好。
Standard 4, needle and category: needle standard will affect the range and accuracy of adhesive in the process of dispensing. When the pressure and nozzle needle are larger, the speed is larger. Therefore, the invasive standard anchor needle of the product manufactured by the machine on the basis of distribution is required. The diameter length of the needle keeps half of the diameter of the glue point, and the effect is very good.
配藥機在配藥過程中的大小是由持續的時間長短決定的，越長越好。根據我們的經驗，調劑量較大。這樣可以保證有足夠的膠水把零件粘在一起，防止形成過多的膠水廢物。
The size of dispensing machine in the dispensing process is determined by the duration of time, the longer the better. According to our experience, the amount of adjustment is large. This can ensure that there is enough glue to stick the parts together to prevent the formation of excessive glue waste.
在點膠機中一般使用環氧樹脂膠、速溶膠、硅膠、無氧膠、UV膠等。
In the dispensing machine, epoxy resin glue, quick sol, silica gel, anaerobic glue, UV glue, etc. are generally used.
7,侵入性壓力直接影響流的速度膠水,膠水,膠水更糟的活動變得厚,它需要更大的壓力,所以我們應該基于配藥機在生產過程中環境溫度和侵入性膠膠量的特性來調節壓力,膠侵入的壓力是通過其內部壓力調節閥進行調理。
7. The invasive pressure directly affects the speed of flow. The worse activities of glue and glue become thicker. It needs more pressure. Therefore, we should adjust the pressure based on the characteristics of the ambient temperature and the amount of invasive glue in the production process of the dispensing machine. The pressure of glue invasion is regulated by its internal pressure regulating valve.
上一篇：打膠機如何防止膠水沉淀？
下一篇：點膠機行業的發展思路！
