淺析風電葉片設備裂紋維護方法
轉子系統是旋轉機械的重要部件，轉子裂紋擴展引起的葉片斷裂對于旋轉機械危害極大。對轉子葉片裂紋振動特性研究較多，對轉子葉片裂紋故障的診斷、識別技術研究較少，而轉子葉片裂紋及其擴展的識別對于終實現葉片裂紋故障的診斷具有重要意義。
The rotor system is an important part of the rotating machinery. The blade fracture caused by the crack propagation of the rotor is very harmful to the rotating machinery. There are many studies on the vibration characteristics of rotor blade cracks, but there are few studies on the diagnosis and recognition technology of rotor blade crack faults. The identification of rotor blade crack and its extension is of great significance for the final diagnosis of blade crack faults.
在機械設備故障診斷中，通常采用基于平穩過程的經典信號處理方法——傅里葉變換分析和加窗傅里葉分析，分別僅從時域或頻域給出信號的統計平均結果，無法同時兼顧信號在時域和頻域的全貌和局部化特征，而這些局部化特征往往是故障的表征。
In the fault diagnosis of mechanical equipment, usually by analysis -- Fu Liye transform and windowed Fu Liye classical signal processing method based on stationary process, were only from the statistical time domain or frequency domain signal is given the average results, not taking into account the whole image and characteristic of signal in time domain and frequency domain, and these features are often localized fault characterization.
裂紋產生的原因應力集中。采用有限元計算分析得出，轉輪在水壓力及離心力的作用下，大應力區主要分布在轉輪葉片周邊上，按第三強度理論計算的相當應力沿葉片周邊分布。一般轉輪葉片存在四個高應力區，他們的位置在葉片進水邊正面(壓力分布面)靠近上冠處；葉片出水邊正面的中部；葉片出水邊背面靠近上冠處；葉片與下環連接區內。
The cause of the crack is caused by stress concentration. The finite element analysis shows that under the action of water pressure and centrifugal force, the large stress area is mainly distributed on the periphery of runner blades, and the equivalent stress calculated by the third strength theory is distributed along the periphery of the blade. There are four high stress zones in general runner blades. Their positions are near the upper part of the inlet side of water inlet (pressure distribution surface) near the upper crown, and the middle part of the front side of the leaf outlet. The leaf outlet is near the upper crown, and the blade is connected with the lower ring connection area.
裂紋無損探傷檢查在大修時對轉輪進行無損探傷檢查，及時處理缺陷，事故隱患是十分必要的。嚴重的裂紋等缺陷用肉眼和放大鏡外觀檢查即可發現，但較細小的缺陷和內部的缺陷必須用無損探傷檢查。
It is very necessary to remove the defects in time and eliminate the hidden trouble. Serious cracks and other defects can be found by the naked eye and magnifying mirror appearance examination, but the smaller defects and internal defects must be inspected by nondestructive testing.
上面講解的便是關于我公司產品的相關信息，希望您滿意小編的講解。我們用滿腔的熱情、無限的激情對待工作和客戶，我們愿意用勤奮的努力和您一起共鑄美好明天！
The above explanation is related information about our company's products, I hope you are satisfied with the explanation of the little editor. We are filled with enthusiasm and passion towards work and customers, we are willing to use the hard work and you create a better tomorrow!
上一篇：雙組份打膠機使用注意事項及使用壽命
下一篇：雙液點膠機的應用及維護方法
