汽車車燈冷膠機的使用基本注意事項
我們平時在使用熱熔膠機時，偶爾會有噴膠量不足的狀況發生，這種問題雖小卻會影響生產進度和使用體驗，解決問題需了解根源所在，今天我們就來了解一下冷膠機日常操作安 全注意事項。
When using the hot melt glue machine, we occasionally have insufficient glue spraying. Although this problem is small, it will affect the production progress and use experience. To solve the problem, we need to understand the root cause. Today, let's learn about the safety precautions for the daily operation of the glue cooler.
1、避免在有揮發原料或氣體的周圍使用PUR熱熔膠機，PUR熱熔膠機噴涂設備周圍不能存放易燃易爆物品。
1. Avoid using pur hot melt adhesive machine around volatile raw materials or gases. Inflammables and explosives shall not be stored around the spraying equipment of PUR hot melt adhesive machine.
2、不要在沒有合適的的保護裝置，并且良好之絕緣體或良好保護面板下操作使用熱熔膠機。
2. Do not operate the hot melt adhesive machine without proper protection device and good insulator or good protection panel.
3、當PUR熱熔膠機需要檢修時必須經過培訓人員方能夠拆機維修。
3. When the pur hot melt adhesive machine needs maintenance, it must be disassembled and repaired by trained personnel.
4、當環境溫度低于-20℃或者環境溫度高于80℃時，不能使用操作PUR熱熔膠機。
4. When the ambient temperature is lower than - 20 ℃ or higher than 80 ℃, the pur hot melt adhesive machine cannot be operated.
5、使用PUR熱熔膠機的場合應保證無快速流動空氣。當PUR熱熔膠機使用的PUR膠桶與熔膠壓盤暴露于快速流通的空氣中時，因急速的冷卻，將影響PUR熱熔膠機的熱熔膠流量，而且浪費能源。
5. Where pur hot melt adhesive machine is used, it shall be ensured that there is no fast flowing air. When the pur glue barrel and glue pressure plate used by the pur hot melt adhesive machine are exposed to the fast circulating air, the rapid cooling will affect the hot melt adhesive flow of the pur hot melt adhesive machine and waste energy.
6、補充PUR熱熔膠時，應檢查PUR熱熔膠桶是否變形，變形嚴重的PUR聚氨酯熱熔膠膠桶應廢棄使用，避免損壞PUR熱熔膠機壓盤。
6. When replenishing pur hot melt adhesive, check whether the pur hot melt adhesive barrel is deformed. The severely deformed pur polyurethane hot melt adhesive barrel shall be discarded to avoid damaging the pressure plate of PUR hot melt adhesive machine.
7、任何時候拆裝PUR熱熔膠機喉管、噴膠膠槍的情況下，都必須立即使用硅油將可能裸露的PUR熱熔膠封住，避免濕反應固化。
7. Whenever the throat of PUR hot melt adhesive machine and glue spraying gun are disassembled, the possible exposed pur hot melt adhesive must be sealed with silicone oil immediately to avoid wet reaction curing.
8、長時間不使用PUR熱熔膠機時，PUR熱熔膠機發熱壓盤圓周上應使用硅油密封，保障膠桶內PUR熱熔膠的性能。
8. When the pur hot melt adhesive machine is not used for a long time, the circumference of the heating pressure plate of the pur hot melt adhesive machine shall be sealed with silicone oil to ensure the performance of the pur hot melt adhesive in the rubber barrel.
以上就是汽車車燈冷膠機的廠家為大家介紹的相關內容，希望可以幫助到大家，更多內容可以之家關注：http://www.666202688.com
The above is the relevant content introduced by the manufacturer of automobile lamp glue cooler. I hope it can help you. More content can be paid attention to by home: http://www.666202688.com
上一篇：中空玻璃生產線廠家為您講解中空玻璃結霧現象
下一篇：雙組份點膠機和雙液點膠機的區別
