雙組份打膠機保養的注意事項
1.壓盤上的放氣閥門要保持曉暢，要定時清洗。
1. The vent valve on the pressure plate shall be kept smooth and cleaned regularly.
2.正常作業時不要斷氣源，假如發現斷氣源應中止作業。
2. Do not cut off the gas source during normal operation. If the gas source is found to be cut off, stop the operation.
3.若雙組份打膠機涂膠作業過程中停頓時刻超過15分鐘以上時，必定要用“沖槍”。本機有報警功能，屆時沒有沖膠會有蜂鳴器報警。
3. If the pause time during the gluing operation of the two-component gluing machine exceeds 15 minutes, the "flushing gun" must be used. The machine has alarm function. If there is no glue flushing, there will be a buzzer alarm.
4.定時查看氣源，應確保使用經干燥的潔凈壓縮空氣，并定時排放別離過濾器中的積水，查看油霧器中的油是否夠用。
4. Check the air source regularly. First, make sure to use dry clean compressed air, regularly discharge the accumulated water in the separate filter, and check whether the oil in the oil mist is enough.
5.硅酮膠B 組份遇空氣會結殼，影響泵的正常作業和管路，因而，停機時B組份膠的一切通道在泄壓后均應關閉，使B組份不得接觸空氣。
5. Component B of silicone adhesive will crust in case of air, affecting the normal operation of the pump and pipeline. Therefore, all channels of component B adhesive shall be closed after pressure relief during shutdown, so that component B shall not contact the air.
6.B膠桶內假如要有空氣，空氣將排不出來，B泵將快速往復運動，不能向高壓泵內正常供膠，影響整個系統，因而，需要將空氣排出來。辦法是：將壓盤提出重新壓入并放氣。
6. If there is air in the rubber barrel B, the air will not be discharged, and the pump B will move back and forth rapidly, which can not supply glue normally to the high-pressure pump, affecting the whole system. Therefore, the air needs to be discharged. The method is: lift the pressure plate, press it in again and bleed.
7.液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調滿意膠嘴正常出膠均勻打膠即可。翻開液壓站時必定要翻開膠槍，否則B組份管路壓力將升得很高，形成事故。
7. The pressure of the hydraulic station system cannot be adjusted too high. It should be adjusted to the satisfaction according to the indoor ambient temperature and other actual conditions. The glue nozzle can discharge glue normally and apply glue evenly. When opening the hydraulic station, the glue gun must be opened, otherwise the pressure of component B pipeline will rise very high, resulting in accidents.
8.A膠提膠泵接連作業1分鐘以上沒有供膠中止，說明管路內有空氣，此刻會報警，須翻開泵上管接頭再翻開A膠提膠泵，直到出膠中止，中止并接好接頭，膠槍會呈現有空氣的嗶嗶爆炸聲，空氣排凈就好了。
8. If the glue supply of a glue lifting pump is not stopped for more than 1 minute, it indicates that there is air in the pipeline. At this time, an alarm will be given. Open the pipe joint on the pump and then open a glue lifting pump until the glue delivery is stopped. Stop and connect the joint. The glue gun will show a beep explosion sound of air, and the air will be discharged.
9.因為每次沖洗混合器不會完全潔凈，每次都有少量的混合膠堆積，越來越多，致使堵塞混合器通道，用一段時刻后，影響出膠量和混合效果，因而要定時(聚硫膠五天，硅酮膠兩天)清洗混合器。把混合器內的混膠棒拆出，如有損壞替換混膠棒。若混膠棒拆不出來，可用火燒掉，留意不能損傷零件螺紋。
9. Because the mixer will not be completely clean every time it is flushed, a small amount of mixed glue accumulates every time, resulting in blocking the mixer channel. After a period of time, the glue output and mixing effect will be affected. Therefore, the mixer should be cleaned regularly (polysulfide glue for five days and silicone glue for two days). Remove the glue mixing rod in the mixer and replace the glue mixing rod if it is damaged. If the glue mixing rod cannot be removed, it can be burned with fire. Be careful not to damage the threads of parts.
The wonderful content of this article is provided by Jinan two-component gluing machine. There are many wonderful contents on this website. You can click to enter more contents: http://www.666202688.com We have special customer service to answer your questions
上一篇：雙組份打膠機設計做好這三點很重要
下一篇：帶你了解一下關于雙組份點膠機注意事項
