有雙組份打膠機的工作原理和適用使用范圍
雙組份自動打膠機工作原理：雙液點膠機是由2個壓力桶（儲存A、B膠水，并通過調整壓力桶內壓力控制A、B膠的出膠比例）,1個是點膠機控制器（通過控制點膠閥的動作而控制出點膠時間和間隔時間），1個雙液點膠閥（由點膠機控制閥體動作從而控制出膠，并可微調A、B膠出膠比例）。A膠和B膠分別從壓力桶出膠口接到點膠閥的A、B進膠口，從點膠閥流出的A、B膠通過三通后在靜態混合管里開始混合，經混合管內的波狀塊不斷反復切割，使兩種膠水充分攪拌，混合均勻后流出。
Working principle of two-component automatic glue applicator: the double liquid glue dispenser consists of two pressure buckets (storing a and B glue and controlling the glue delivery ratio of a and B glue by adjusting the pressure in the pressure bucket), and one is the glue dispenser controller (controlling the glue dispensing time and interval by controlling the action of the glue dispensing valve), 1 double liquid dispensing valve (the dispensing machine controls the action of the valve body to control the glue output, and can fine tune the glue output ratio of a and b). Glue a and B are respectively connected from the glue outlet of the pressure barrel to the glue inlet a and B of the dispensing valve. After passing through the tee, the glue a and B flowing out of the dispensing valve begin to mix in the static mixing pipe, and are continuously and repeatedly cut by the wavy block in the mixing pipe to fully stir the two kinds of glue and flow out after mixing evenly.
雙組份自動打膠機主要適用于:
The two-component automatic glue applicator is mainly applicable to:
LED燈條的灌膠、燈具、水晶工藝品的灌膠、電子點火器、高頻變壓器的灌膠封裝、離子發生器的灌封、充電器的灌膠、手機按鍵點膠、手機電池封裝、筆記本電池封裝、線圈點膠、IC 封膠、喇叭外圈點膠、 PDA 封膠、 LCD 封膠、機殼粘接等電子產品加工、光學器件加工、機械密封等應用。
Glue filling of LED light strip, energy-saving lamps, crystal crafts, electronic igniter, glue filling and packaging of high-frequency transformer, ion generator, charger, mobile phone key dispensing, mobile phone battery packaging, notebook battery packaging, coil dispensing, IC sealing, horn outer ring dispensing, PDA sealing, LCD sealing, casing bonding and other electronic product processing Optical device processing, mechanical sealing and other applications.
主要部件介紹：
Introduction to main components:
1、微電腦控制的數顯點膠機控制器：使點膠精度更精確，并且有自動，定量和循環等多種操作模式。數字按鈕設定、LED顯示時間、直觀、方便。循環點膠功能，可實現自動化流水生產線間隔所需時間自動點膠。
1. Microcomputer controlled digital display dispenser controller: it makes the dispensing accuracy more accurate, and has a variety of operation modes such as automatic, quantitative and circulation. Digital button setting, LED display time, intuitive and convenient. The circulation dispensing function can realize the automatic dispensing at the interval required by the automatic flow production line.
2、精密雙液點膠閥：由點膠機控制出膠，點膠閥尾部調節螺絲和膠水的壓力可控制出膠量大小。調節螺絲順時鐘向下轉動為減小膠量，逆時鐘方向轉動為 加大膠量。
2. Precision double liquid dispensing valve: the dispensing is controlled by the dispensing machine. The amount of glue can be controlled by adjusting the pressure of screw and glue at the tail of the dispensing valve. Turn the adjusting screw clockwise to reduce the glue amount, and counterclockwise to increase the glue amount.
3、靜態混合管的混合方式為靜態混合，由一連串左右旋葉片相互垂直排列在套管內組成，A、B膠水經過靜態混合管時進行連續的切割與重合為均勻的混合液。靜態混合管出口部可接任何口徑的針頭，以保證出膠量精確。混合管可重復使用，工作結束后拔掉混合管并將之泡在丙酮，酒精，天那水等溶劑里進行清洗，下次工作可繼續使用。
3. The mixing mode of the static mixing pipe is static mixing, which is composed of a series of left and right rotating blades vertically arranged in the casing. When a and B glue pass through the static mixing pipe, they are continuously cut and overlapped to form a uniform mixing liquid. The outlet of the static mixing tube can be connected with a needle of any caliber to ensure accurate glue output. The mixing tube can be reused. After the work, pull out the mixing tube and soak it in acetone, alcohol, Tianna water and other solvents for cleaning. It can be used again in the next work.
4、2個壓力桶：膠水分裝，長時間不固化。通過調節兩個壓力桶的氣壓，可以方便地調節膠水的出膠比例在1：13：1。對流動性差、粘稠度大的膠水可選裝加熱裝置，確保膠水有較好的流動性。對于長時間放置會沉淀的膠水可根據需要加裝手動、電動攪拌功能。壓力桶材質有不銹鋼和碳鋼可選。
4. 2 pressure drums: glue is sub packed and does not solidify for a long time. By adjusting the air pressure of the two pressure barrels, the glue output ratio can be easily adjusted from 1:1 to 3:1. Heating device can be selected for glue with poor fluidity and high viscosity to ensure good fluidity of glue. For glue that will precipitate after a long time, manual and electric mixing functions can be added as needed. The pressure barrel is made of stainless steel and carbon steel.
5、壓力桶的清洗方便快捷，并可根據用戶的需要可另配置不銹鋼內膽。將壓力桶內的膠水換成清洗液（清水/天那水/酒精/丙酮），高壓力將清洗液從膠槍打出，可膠槍內殘余膠。在常溫下分裝在A、B壓力桶內的膠水如不固化或沉淀，工作結束后無需清理
5. The cleaning of the pressure barrel is convenient and fast, and the stainless steel liner can be configured according to the needs of users. Replace the glue in the pressure barrel with cleaning fluid (clean water / Tianna water / alcohol / acetone), and shoot the cleaning fluid from the glue gun under high pressure to remove the residual glue in the glue gun. If the glue sub packed in pressure drums A and B at normal temperature does not solidify or precipitate, it does not need to be cleaned after the work is completed
上一篇：帶你了解一下關于雙組份點膠機注意事項
下一篇：打膠時中空玻璃起霧怎么辦？
