點膠機與灌膠機的區別有哪些？
很多人在問，點膠機和灌膠機有什么區別？不就是專門對流體控制的自動化設備嗎，那區別又在哪里。下面我們先來認識什么是灌膠機、點膠機，區別又在哪里。
Many people are asking, what is the difference between dispensing machine and filling machine? Isn't it the automatic equipment for fluid control? What's the difference. Now let's first understand what is glue filling machine and dispensing machine, and what's the difference.
一、什么是點膠機？
1、 What is a dispensing machine?
點膠機也叫灌膠機，是專門對流體進行控制的設備。主要將流體點滴、涂覆于產品表面或產品內部的自動化機器，可實現三維、四維路徑點膠，定位控膠準，不拉絲，不漏膠，不滴膠。
Dispensing machine, also known as glue filling machine, is a special equipment for fluid control. The automatic machine mainly drips and coats the fluid on the product surface or inside the product, which can realize three-dimensional and four-dimensional path dispensing, positioning and accurate glue control, no wire drawing, no glue leakage and no glue dripping.
二、什么是灌膠機？
2、 What is a glue filling machine?
灌膠機，是專門對流體進行控制的設備，并將液體點滴、涂覆、灌封于產品表面或產品內部的自動化機器，使其達到密封、固定、防水等作用的設備，一般使用的多為雙組份膠水。
Glue filling machine is an automatic machine that specially controls the fluid and drips, coats and seals the liquid on the surface or inside of the product to achieve the functions of sealing, fixing and waterproof. Generally, two-component glue is used.
三、灌膠機和點膠機區別：
3、 Difference between glue filling machine and dispensing machine:
1、控膠方式不同：目前市場上大部分的點膠機都還是主要是靠氣壓來控制出膠的，當然現在也有不用氣壓控制的。而灌膠機主要就是靠計量泵來控制出膠的，通過調節泵的轉速來調節出膠量的大小。
1. Different glue control methods: at present, most dispensing machines in the market mainly rely on air pressure to control the glue output. Of course, there are also some without air pressure control. The glue filling machine mainly depends on the metering pump to control the glue output, and the glue output is adjusted by adjusting the speed of the pump.
2、出膠量大小不同：相對來說，灌膠機出膠量大于點膠機，而灌膠機的出膠量較大，能達到十幾到二十幾克每秒，而點膠機的出膠量較小。
2. Different sizes of glue output: relatively speaking, the glue output of the glue dispenser is greater than that of the glue dispenser, while the glue output of the glue dispenser is large, which can reach more than ten to twenty grams per second, while the glue output of the glue dispenser is small.
3、點膠精度不同：通常點膠機用膠量小、精度高，而灌膠機用膠量大，用膠精度略低。
3. Different dispensing accuracy: generally, the dispensing machine uses a small amount of glue and has high precision, while the glue filling machine uses a large amount of glue and has a slightly lower precision.
4、適用膠水不同：點膠機適用單液（單組份）膠水的產品工藝用膠。灌膠機適用雙液（雙組份，也叫AB膠）膠水，的產品工藝用膠，兩者之間相差很大。
4. Different applicable glues: the dispensing machine is suitable for the product process glue of single liquid (single component) glue. The glue filling machine is suitable for two-liquid (two-component, also known as AB glue) glue. There is a great difference between the two.
The above is a detailed introduction to the two-component gluing machine. I hope it will be helpful to you If you have any questions, you are welcome to contact us We will provide you with professional service http://www.666202688.com
上一篇：為什么選擇雙組份自動點打膠機
下一篇：雙組份打膠機的安裝
