打膠機設備平常使用中要進行定期檢查
雙組份打膠機在咱們平常的運用過程中有許多需求留意的事項，假如咱們平常不留心留意這些當地很可能會形成咱們的雙組份打膠機出現各種各樣的故障，這樣不光影響你的生產功率下降你的收益還會大幅度的下降設備的壽數。總之打膠機設備平常使用中要進行定期檢查，下面小編為您講解。
There are many things we need to pay attention to when using two-component glue dispensers. If we don't pay attention to these places, it is likely that our two-component glue dispensers will have various failures, which will not only affect your production power, but also greatly reduce your income and the life of the equipment. In a word, the glue dispenser equipment should be inspected regularly during normal use. The following sections will explain to you.
●清潔噴槍表面、清理噴嘴，確保噴嘴的暢通;
● Clean the surface of the spray gun and the nozzle to ensure that the nozzle is unblocked;
●清潔或替換雙組份打膠機和噴槍的過濾網;
● Clean or replace the filter screen of two-component sealant dispenser and spray gun;
●查看噴槍是否有漏膠現象，如有漏膠現象請調理，維修、替換噴槍、噴頭、噴嘴等需求替換的部件。
● Check whether the spray gun has glue leakage. If there is glue leakage, please adjust, repair and replace the spray gun, nozzle, nozzle and other parts that need to be replaced.
●查看膠缸內壁是否有炭化層，如有炭化層請運用諾信專用清洗液R溶劑清洗膠缸。
● Check whether there is a carbonized layer on the inner wall of the rubber cylinder. If there is a carbonized layer, please use the special cleaning solution R solvent of Nuoxin to clean the rubber cylinder.
●將雙組份打膠機加熱操作溫度，排空膠箱內的熱溶膠。查看膠缸內是否有雜質，如有雜質用干凈的抹布清潔膠缸。
● Heat the two-component sealant beater to the operating temperature, and drain the hot glue in the glue box. Check whether there are impurities in the rubber cylinder. If there are impurities, clean the rubber cylinder with a clean rag.
●查看一切接線盒和接線柱是否結實;
● Check whether all junction boxes and terminals are solid;
●查看一切電源銜接線是否有破損現象，其他絕緣件是否牢靠;
● Check whether all power cord connections are damaged and whether other insulating parts are secure;
●清潔及查看雙組份打膠機電器箱內部;
● Clean and check the interior of the electrical box of the two-component sealant dispenser;
●查看一切電源銜接線銜接是否牢靠。
● Check whether all power supply cables are connected securely.
此外由于雙組份打膠機每次沖刷混合器不會很干凈，每次都有少量的混合膠堆積，越來越多，致使堵塞混合器通道，用一段時間后，影響出膠量和混合作用，因而要定時(聚硫膠五天，硅酮膠兩天)清洗混合器。把混合器內的混膠棒拆出，如有損壞替換新的混膠棒。若混膠棒拆不出來，可用火燒掉，留意不能損害零件螺紋。
In addition, since the two-component rubber beater is not very clean each time it washes out the mixer, a small amount of mixed glue accumulates each time, which leads to blockage of the mixer channel. After a period of time, the glue output and mixing effect will be affected, so the mixer should be cleaned regularly (five days for polysulfide glue and two days for silicone glue). Remove the glue mixing rod in the mixer and replace it with a new one if it is damaged. If the rubber mixing rod cannot be removed, it can be burned off. Be careful not to damage the thread of the part.
The above is what Xiaobian explained to you about the glue dispenser. You can come to our website at any time if you have any needs http://www.666202688.com For consultation, relevant personnel will serve you wholeheartedly!
上一篇：雙組份打膠機換桶的操作細節
下一篇：打膠機自動打膠的基本過程
