雙組份打膠機的一些操作規程事項
雙組份打膠機具有操作準確、效率快、品質好等優勢，對于實現企業大批量生產有著關鍵性作用。而雙組份打膠機作為自動化機械設備，在操作方面有著嚴格的要求。下面小編為您講講雙組份打膠機的一些操作規程事項。
The two-component sealant dispenser has the advantages of accurate operation, fast efficiency and good quality, which plays a key role in realizing mass production of enterprises. As an automatic mechanical equipment, the two-component rubber beater has strict requirements in operation. The following section will tell you about some operating procedures of two-component sealant dispenser.
雙組份打膠機操作規程：
Operating procedures of two-component sealant dispenser:
1、在安裝雙組份打膠機時，需要產品的固定架，打開氣壓、機器電源，在膠管內灌入需要使用的膠水，固定好膠管使用高度；
1. When installing the two-component sealant dispenser, you need the fixed frame of the product, turn on the air pressure and machine power, fill the required glue into the rubber tube, and fix the use height of the rubber tube;
2、編程：根據產品點膠圖形，編制程序。程序編好后設置點膠速度、Z軸提高高度相對值、點膠時間參數；
2. Programming: according to the product dispensing graphics, prepare the program. After programming, set dispensing speed, relative value of Z-axis height increase and dispensing time parameters;
3、氣壓設定：根據膠水粘稠度設置對應使用氣壓；
3. Air pressure setting: set the corresponding air pressure according to the glue viscosity;
4、程序、設置完成后，按下機器上的RUN/TEACH開關，放置產品按下Start鍵開始點膠，每換產一只產品，都需按下Start鍵；
4. After the program and settings are completed, press the RUN/TEACH switch on the machine, place the product and press the Start key to start dispensing. Press the Start key every time a product is changed;
5、完成點膠工作后或中途長時間不進行點膠工作時，需及時清洗針頭，以防針頭堵塞。
5. After the dispensing work is completed or when the dispensing work is not carried out for a long time, the needle shall be cleaned in time to prevent the needle from blocking.
此外要知道，在使用雙組份打膠機之前，在操作設備之前，廠家的操作工作人員須完全了解雙組份打膠機的操作。啟動機器前，檢查電源和電壓是否穩定。開機后，應該注意機器是否發出異常噪音。如果是，應立即關閉機器，并在檢查問題后打開機器。
In addition, before using the two-component sealant dispenser and operating the equipment, the manufacturer's operating personnel must fully understand the operation of the two-component sealant dispenser. Before starting the machine, check whether the power supply and voltage are stable. After startup, pay attention to whether the machine makes abnormal noise. If so, shut down the machine immediately and turn it on after checking the problem.
The above contents are about the operating procedures of two-component sealant dispenser, and I believe you have already understood them. It is recommended that you do a good job of relevant inspections before use to promote the smooth use of high-quality products. More relevant content will come to our website http://www.666202688.com Consult and understand!
上一篇：雙組份打膠機在平常生產操作中的留意事項
下一篇：幾點關于雙組份打膠機的點膠知識要點
