建議使用雙組份打膠機之前行調試
為了讓生產的效率更高，雙組份打膠機在在正式投入生產之前是需要花點時間去調試的，尤其是要去設置程序，同時有很多的配件都需要調試，那么怎么調試
雙組份打膠機呢？
In order to make the production more efficient, it takes some time to debug the two-component sealant dispenser before it is officially put into production, especially to set up the program. At the same time, many accessories need to be debugged. How to debug the two-component sealant dispenser?
1、機臺擺放位置的水平
1. The levelness of the machine table placement position
雙組份打膠機的調試要保持雙組份打膠機平臺水平度，打好平臺水平相當于調試好了一半，不然則容易出現點偏、多膠少膠、溢膠等問題。
For the commissioning of two-component sealant dispenser, the levelness of the two-component sealant dispenser platform shall be maintained. A good platform level is equivalent to half of the commissioning. Otherwise, problems such as point deviation, more glue, less glue and overflow are likely to occur.
2、選擇合適的針頭
2. Select the right needle
自動雙組份打膠機針頭內部的直徑應該和膠點直徑的1/2左右，可根據產品大小來選取合適的點膠針頭，針頭小內徑為0.1毫米。
The inner diameter of the needle of the automatic two-component dispensing machine should be about 1/2 of the diameter of the glue point. The proper dispensing needle can be selected according to the size of the product. The small inner diameter of the needle is 0.1mm.
3、點膠針頭與點膠位置的高度距離調節
3. Height distance adjustment between dispensing needle and dispensing position
雙組份打膠機需要調試點膠高度，針尖到產品的距離過高，會出現拉膠問題；點膠高度太低又會出現針頭沾膠、爬膠、膠量不均勻等問題。
The two-component glue dispenser needs to adjust the dispensing height. If the distance between the needle tip and the product is too high, the glue pulling problem will occur; If the dispensing height is too low, problems such as glue sticking on the needle, glue creeping, and uneven glue amount will occur.
4、出膠時間的調試
4. Commissioning of dispensing time
自動雙組份打膠機的點膠量的設定應該為產品間距的1/2，保證有足夠的點膠量粘貼組件，防止過多的膠水滲出；調試出膠時間可以控制好點膠量。
The dispensing amount of the automatic two-component sealant dispenser should be set at 1/2 of the product spacing, so as to ensure that there is enough dispensing amount to paste the components and prevent excessive glue from seeping out; Adjust the dispensing time to control the dispensing amount.
5、壓力設定調試
5. Pressure setting commissioning
雙組份打膠機的控制器把壓力提供給膠管和針頭，通過調節雙組份打膠機壓力大小，可以控制出膠量和點膠的速度，壓力過強容易出現膠水噴出的問題，壓力太弱則會出現點膠不均勻和漏點的現象。
The controller of the two-component glue dispenser supplies pressure to the rubber tube and needle. By adjusting the pressure of the two-component glue dispenser, the amount of glue and the speed of dispensing can be controlled. If the pressure is too strong, the problem of glue spraying is likely to occur. If the pressure is too weak, the phenomenon of uneven dispensing and leakage will occur.
6、膠水溫度控制
6. Glue temperature control
一般環氧樹脂膠水應保存在0～5℃的冰箱中，使用時提前半小時拿出，使膠水溫度與工作環境一致，膠水的使用溫度應為23℃～25℃，注意對環境溫度進行控制。
Generally, the epoxy resin glue should be stored in a refrigerator with a temperature of 0~5 ℃. Take it out half an hour in advance to make the glue temperature consistent with the working environment. The glue should be used at a temperature of 23 ℃~25 ℃. Pay attention to the control of the ambient temperature.
After the debugging of these steps, the two-component sealant machine can be put into operation automatically. Debugging is to improve the production efficiency and prevent the production from being affected by faults in the working process. Therefore, operators need to learn how to debug the two-component sealant dispenser. More relevant content will come to our website http://www.666202688.com Consult!
上一篇：打膠機的液壓缸工作不正常原因及維護
下一篇：通過打膠機保養調試能使點膠效果更好
