中空玻璃打膠機在操作時要注意什么？
1、停電時馬上到機器后面交換正在使用的排膠閥氣管后，手動按動白膠電磁閥使氣泵上下運動排膠到全白膠時停止。氣管接回原處，結束。
1, when the power immediately to the machine behind the exchange is used after discharging valve pipe, manual press glue electromagnetic valve to make the pump up and down movement to stop discharging glue. Return the trachea to its original place and end.
2、生產時需要把玻璃里面一張標簽撕掉或貼到玻璃的下方，防止光電感應開關感應到誤動作損壞膠頭。在自動狀態時注意不要用手或其他異物遮擋光電開關，有問題時及時按下急停開關或關閉電源。
2, the production need to put a glass inside the label affixed to the bottom of the glass or the photoelectric switch to prevent misoperation damaged plastic head induction. In the state of automatic attention do not use hand or other foreign bodies from the photoelectric switch, there are problems in time when pressing the emergency stop or turn off the power switch.
3、下班時需要清理膠頭，關閉連線，把旋轉開關旋轉到清洗和手動狀態，按下排膠啟動鍵，再按排膠閥鍵，這時膠頭出膠，打開黑膠減壓閥發排壓，降下壓力后關閉擰緊，待膠頭出膠全是白膠后按下排膠閥鍵，間隔5秒左右再次按下排膠閥鍵降白膠壓力，待壓力降到1以下關閉排膠閥。 ！！！《雙系統》注意：泄黑膠壓力時必須把兩組黑膠壓力都泄完。
Need to clean the rubber head 3, work, first close the connection, the rotary switch is rotated to the manual cleaning and discharging state, press the start button, then press button when discharging valve, rubber head glue, open the black glue valve pressure drop under pressure after publishing, close to tighten, head is full of glue glue according to the lower glue glue valve key, the interval of about 5 seconds Press the rubber drain button again to reduce the pressure of the white glue and close the rubber drain valve when the pressure drops below 1.!!! Attention to "double system": when the black rubber pressure is released, two groups of black rubber pressure must be exhausted.
4、每條邊的打膠情況可通過工藝里面的向上調整，上部調整，向下調整，底部調整來適當調整，每次調整需保存。
4, each side of the glue can be through the process inside the upward and downward adjustment, the bottom of the upper adjusting, adjustment to adjust, adjust each need to save.
5、中途需要更換玻璃厚度或綠條厚度時，待生產上次規格玻璃后一張玻璃時關閉連線，打完后一張玻璃進入輸出端停下時轉到手動狀態，進入玻璃厚度界面設置需要的玻璃厚度或綠條厚度，設置完成以后連線自動生產。
5, midway need to replace the glass thickness or green strip thickness, close the connection to the last production specifications of glass last piece of glass, finished the last piece of glass to the manual state into the output end stop when the thickness of the glass into the interface settings need glass thickness or green strip thickness, set up after the completion of the automatic production line.
6、需要排膠時先關閉連線，待打膠的玻璃打完并移動到輸出端以后按下排膠啟動按鈕，再按排膠閥。這時需要繼續生產就需要把設備旋轉到手動狀態，按下連線按鈕，再次轉到自動狀態，按下自動運行按鈕繼續生產。
6, you need to close the connection when discharging, after the glue glass finish and moves to the output end of discharging press the start button, then press the discharging valve. The need to continue production requires the equipment rotation to the manual state, press the connect button again to automatic state, press the automatic operation button to continue production.
7、打膠時若膠頭殘余膠較多時需及時清理，清理時注意防止輔助傳送傷手，玻璃平整度不好時需要用手輔助玻璃，必須使檢測器在兩片玻璃之間移動。
7, if the adhesive glue head residual glue more the need for timely cleaning, cleaning Caution! Auxiliary transmission to prevent hand injury, glass flatness is not good when the auxiliary glass by hand, must make the detector moving between two pieces of glass.
A two-component small sum atx-ii above, hope to help customers, if what you do not understand or seek help please click on our official website: http://www.666202688.com or contact us, we will do our best for you to solve
上一篇：雙組份打膠機的注意事項
下一篇：點膠機電機不復位的解決方法！
